Mechanical

Yield Strength

The stress at which a material begins to deform permanently (plastically). Below yield strength, deformation is elastic and reversible.

  • Symbol: σ_y (MPa)
  • Determined from stress-strain curve (0.2% offset method)
  • Critical for structural design — parts must operate below yield to avoid permanent deformation

Surface Roughness

A quantitative measure of the texture/finish of a machined surface, typically expressed as Ra (arithmetic average roughness).

  • Ra — average deviation from the mean line (µm)
  • Lower Ra = smoother surface
  • Affected by: tool condition, feed rate, cutting speed, material
Finish Type Typical Ra (µm)
Fine grinding 0.1 – 0.4
Turning 0.8 – 3.2
Milling 1.6 – 6.3
As-cast 6.3 – 25

Tolerance Stack-up

The cumulative effect of individual part tolerances in an assembly. When multiple parts are assembled, their tolerances combine — potentially causing fit or function issues.

Two analysis methods:

  • Worst-case: Sum of all tolerances (conservative, guarantees 100% assembly)
  • Statistical (RSS): Root sum of squares — assumes normal distribution, allows tighter design with acceptable risk

Tolerance stack-up analysis is critical for multi-part assemblies where clearance or interference must be controlled.

Ultimate Tensile Strength

The maximum stress a material can withstand while being stretched or pulled before necking and fracture.

  • Symbol: σ_uts or σ_u (MPa)
  • Found at peak of engineering stress-strain curve
  • Used for calculating factor of safety against fracture
  • Note: different from true stress at failure

Modulus of Elasticity (Young's Modulus)

A measure of material stiffness — the ratio of stress to strain in the linear elastic region.

  • Symbol: E (GPa)
  • Slope of stress-strain curve in elastic region
  • Steel ≈ 200 GPa, Aluminum ≈ 70 GPa
  • Higher E = stiffer material

Poisson's Ratio

The ratio of lateral strain to axial strain when a material is loaded axially.

  • Symbol: ν (nu)
  • Typically 0.25–0.35 for metals
  • 0.5 for incompressible materials (rubber)
  • Negative values exist for auxetic materials

Stress Concentration

Localized increase in stress near geometric discontinuities (holes, notches, keyways).

  • kt = theoretical stress concentration factor
  • Causes: sudden cross-section changes, sharp corners
  • Mitigate with: fillets, gradual transitions
  • Critical under cyclic loading (fatigue)

Factor of Safety

The ratio of a material's strength to the applied stress, providing a design margin.

  • FoS = σ_allow / σ_applied
  • Based on yield (prevent plastic deformation) or ultimate (prevent fracture)
  • Typical values: 1.5–5.0 depending on application
  • Higher for safety-critical or uncertain loading

Fatigue

Failure under cyclic loading at stresses below yield strength. Progresses through crack initiation, propagation, and sudden fracture.

  • Characterized by S-N curves (stress vs. cycles)
  • Fatigue limit (steel) ≈ 0.5 × σ_uts
  • Aluminum has no true fatigue limit
  • Affected by: surface finish, mean stress, environment

Buckling

Elastic instability of slender members under compressive load. Sudden lateral deflection at critical load.

  • Euler buckling: P_cr = π²EI/(KL)²
  • Governs design of columns and slender struts
  • Failure can occur below material yield strength
  • slenderness ratio (KL/r) determines behavior

Thermal Stress

Stress induced in a constrained material due to temperature change.

  • σ = EαΔT (for unconstrained thermal expansion)
  • α = coefficient of thermal expansion
  • Can cause buckling or fracture if constrained
  • Critical in assemblies with mismatched thermal expansion

Hardness

Resistance to localized plastic deformation. Often correlated with strength.

Test Scale
Brinell (HB) 500 kg load
Rockwell (HRC/HRB) Scale-specific
Vickers (HV) 1-1200 kg
  • Higher hardness generally means higher strength but lower ductility

Toughness

Ability to absorb energy before fracture. Combination of strength and ductility.

  • Impact toughness: measured by Charpy/Izod tests
  • Fracture toughness (K_IC): resistance to crack propagation
  • Higher toughness = more ductile, less brittle

Creep

Time-dependent deformation under sustained load at elevated temperature.

  • Significant above ~0.4 × T_melt (in Kelvin)
  • Three stages: primary (decelerating), secondary (steady), tertiary (accelerating to failure)
  • Critical in: turbine blades, nuclear reactors, high-T applications
  • Design based on stress to produce 1% strain in 100,000 hours

GD&T (Geometric Dimensioning and Tolerancing)

A standardized system (ASME Y14.5) for defining part geometry and allowable variation using symbolic language on engineering drawings.

  • Replaces ± coordinate tolerances with feature-based controls
  • Key controls: flatness, perpendicularity, true position, concentricity, runout
  • Ensures functional fit and interchangeability regardless of manufacturer
  • Critical for communicating design intent to machining and inspection

DFM (Design for Manufacturability)

Engineering practice of designing parts to be easier, cheaper, and more reliable to manufacture.

  • Minimize number of parts, reduce tight tolerances where possible
  • Choose features compatible with available processes (drilling vs. milling, etc.)
  • Evaluate early — changes are cheap at design stage, expensive in production
  • Closely linked to tolerance stack-up and material selection

FEA (Finite Element Analysis)

Numerical simulation technique that divides a model into small elements to approximate stress, heat, or other physical quantities.

  • Used to predict failure, optimize geometry, and replace physical prototypes
  • Common tools: ANSYS, Abaqus, SolidWorks Simulation
  • Results are only as valid as mesh quality, material data, and boundary conditions

FMEA (Failure Mode and Effects Analysis)

A structured, proactive method for identifying potential failure modes in a design or process and assessing their impact.

Column Description
Failure Mode How could this fail?
Effect What happens when it fails?
Severity (S) How bad is the effect? (1–10)
Occurrence (O) How likely is failure? (1–10)
Detection (D) How likely is it caught? (1–10)
RPN Risk Priority Number = S × O × D
  • High RPN items are prioritized for redesign or additional inspection
  • Required in IATF 16949 (automotive) and ISO 13485 (medical devices)

AOI (Automated Optical Inspection)

Machine vision system that automatically inspects parts or PCBs for surface defects, dimensional deviations, or missing features.

  • Replaces or augments manual visual inspection
  • Uses cameras, structured light, or laser profiling
  • Output: pass/fail classification + defect location
  • The application context for industrial CV projects (PatchCore, YOLOv8 segmentation)